【 Weak current College 】 interface, install different — scanner installation experience

Refer to the scanner's installation operation, many friends on this topic so topic sneer, simpler than it is worth mentioning, as long as the scanner and the computer is connected properly, the system will automatically recognize it, then the wizard prompts the installed drivers will be able to complete the installation of the scanner. Having said that, but in the actual installation of the scanner, you will find different interface scanner have different installation methods; to help fellow rookie friends successfully installed the scanner, this article here on different interface scanner installation methods respectively, hope useful to everybody!

General interface Setup

In the meantime, use common interfaces of the scanner has not much to see that this interface through common in older scanner. During the installation of ordinary interface scanner, the first thing we do is physically connected to the signal cable to the scanner and the back of the head of "PortA" flag port connection, and another one with the corresponding port on your computer.

After the scanner's power plug and outlet connection, then the scanner's power switch is turned on, to power on, start the scanner; after a few seconds to start the computer system, so the scanner attached to your computer can be automatically recognized by Windows System. Subsequently, the system will pop up a scanner Setup Wizard interface, we can according to the tips, the scanner random equipped with driver installation CD into your computer CD drive, and then let the system automatically searches for the driver and complete the driver installation. Driver installation is complete, the system sometimes smart reminder to test scanner installation if the installation is successful, the screen will show the corresponding success action prompts, if the test fails, the system will list the possible failure, in which case we just follow the prompts to reexamining the installation!

Since the scanner is working need relevant software applications, so installing the scan driver, we also need the random allocation of scanning software installed, install the scanner software and open it in the program interface, then in turn executes the menu bar "file"/"Select source" command, select the scanner just now installed the destination presentation correctly on the scanner glass, and then do one of the applications in the "scanning" command to see which scanner is able to scan into the image presentation, if you can scan, it indicates that the scanner has been able to work properly.

Small Tip: General interface for your scanner if you installed in the lower version of the operating system, most likely will not be seen by the operating system automatically recognizes. At this point we need to follow these instructions for installing the scanner driver:



First click the "start"/"settings"/"Control Panel" command, open the System Control Panel window, double-click the "add new hardware" icon in the resulting wizard interface, gradually click "next" button when prompted, "do you want to install the device in the device list appears," we can "do not, the device is not in the list" item is checked, and click "next" button; when the wizard window prompt we "need Windows search for new hardware?" We can be "no, I want to select from the list to select the hardware" (as shown in Figure 1), then eject the device list, select "other equipment" project, and then click "next" button, enter into such as shown in Figure 2 of the wizard window; click the "have disk" button, then the file selection dialog box, select the scanner driver CD for driver file, and then press the default prompts to complete the scanner driver installation tasks.

The installation of the SCSI interface

SCSI interface is a scanner a common port type, install this interface scanner is usually higher than the preceding an interface-type complex. The SCSI interface scanner physical connections, we first need to open the computer chassis, take a look at whether there are idle in the motherboard's PCI slots, if any, the scanner with a SCSI card tightly into the motherboard free slots, and use the card to laminate with screws to the chassis cover.

Then open the computer power switch to start the computer system to start successfully after the system will automatically recognize the installation to the system board SCSI card, and will pop up a prompt to insert the card in our Setup disk, in which case we just follow the prompts to properly placed in the corresponding SCSI card setup disk, and then make sure to answer, the system can automatically install the driver for the SCSI card.

The following exit Windows system and turn off the computer power switch, and then randomly with SCSI signal cable is attached to a SCSI card and the other side and the corresponding interface in the scanner, then power up the scanner's power, then plug in the computer's power supply, so Windows system will automatically identify the connection in the SCSI card scanner device, at this point we only need to install the above to install the scanner driver.

If your computer at the same time connect several SCSI devices, we also need to separately on each SCSI peripherals ID labels to settings to ensure that their labels, otherwise the system will not be able to accurately identify the connection in the SCSI card scanner, or you will be prompted for a hardware device. Finished good scanner driver task, we also need to follow the previous steps, complete good scanner related application software installation work!

Small Tip: If the SCSI interface scanner connected to your computer, Windows system does not recognize them, we should first check scanner and calculationMachine in the physical connection is correct, secure, and confirm the SCSI card installation order is correct. In the exclusion of the above factors, we may wish to directly open the scanner's optical Setup window, and double-click the CD "setup.exe" file, when prompted, we can't find your scanner, you must install the driver continues, when the driver installation is completed, and then restart the computer system, this system might also be able to identify the scanner.

USB install

Moment, the vast majority of scanners now start using the USB interface, because the interface of a simple scanner installation operation, even if relative never approached the scanner's friends can quickly get started. No matter what brand and what type of scanner, its basic installation method is the same:

In a physical connection, as long as the scanner's USB plug into the corresponding port on your computer, and then look at the scanner back panel in CCD elements are fixed, if you have already fixed it must be unlocked; the following are open the scanner and the power switch on the computer so that Windows system should be able to automatically recognize your USB scanner.

In accordance with the instructions on the screen, after the scanner driver CD into the CD drive, and then use the manual method, the positioning of the driver CD goal driven file selected, the following and then press the default prompts to complete the remaining work you can. When the scanner is installed, we can use its own scanning application software, to open the application interface, select the destination for presentation Scan scanner. Of course, there's the scanner before installing the driver, it cannot be be connected to a computer's USB port, but is waiting for the drivers installed after the scanner and computer are connected, otherwise you will be prompted to find a scanner.

Small Tip: now many scanner driver CD, contains several different operating system driver, or contains several different interface types of drivers, so if you install the driver, let the system automatically searches the installation CD of drivers, often occur various strange fault. For example, have a friend in the installation of the scanner, press the default prompt of the wizard window to let the system automatically searches for the CD driver files, the installation is complete, the scanner will work; however, the computer system after rebooting, the screen should appear "found new hardware" prompt, and then install a drivers also exhibits the same behavior. Just started my friends thought it was a driver CD itself has a problem, when you try to access the contents of the disc, find below the root directory contains several different ports of subfolders, such as "usb" folder, such as "scsi" folder. The original system to automatically search for CD scan driver file, it will often be causing scan position port driver installation is not accurate, so when the system restarts, it will prompt you to discover new devices. If we now use manual positioning method, first install scan ports, and then install the scanner driver, thus ensuring the installation operation successful!