【 Weak current College 】 why post to press F1 to enter system---Power By 【 China power house network 】

No need to press the F1 key to enter, mainly because the BIOS settings does not match the real hardware data, can be divided into the following situation:
1, actually do not have a floppy disk drive or floppy disk drive is broken, and the BIOS is set to the floppy drive, this led to press F1 to continue.
2. the original of the hanging two hard drives in the BIOS is set to double hard drive, then take off one when we forget the BIOS setting to come back, the problem may also occur.
3. motherboard battery has a will result in data loss to occur this failure.
4. reboot the system, enter BIOS settings and found that the floppy was set to 1.44M, but actually there is no floppy drive in the chassis, this key is set to NONE, troubleshooting.

There was a lot of people ask this question, the following to this type of problem do you sum up, I hope to everyone to help.
1、HarewareMonitorfoundanerror，enterPOWERMANAGEMENTSETUPfordetails，PressF1tocontinue，DELtoenterSETUP

Chinese: monitoring features found error, enter detailed information, see POWERMANAGEMENTSETUP press F1 to continue the boot process, press DEL to enter the COMS set.

Explanation: some motherboards have hardware monitoring feature, you can set the motherboard and CPU temperature monitor, voltage regulator of voltage output bit monitor and on each fan speed monitoring, when

The monitoring features in the post is found to have abnormal situation, then it will appear above this line, then you can enter the COMS set select POWERMANAGEMENTSETUP, in the right ** FanMonitor **, ** ThermalMonitor ** and ** VoltageMonitor ** view which part issued an exception, and then to be addressed.

2、prislavedrive-ATAPILNCOMPatiblepressF1toResume
May be you haven't connected or the optical drive is defective, the best in the CMOS will all IDE port is set to automatic.

3、PressF1tocontinue,DELtoenterSETUP
Power on and press DEL to enter the BIOS, select floppy driveselect NONE and press F10 to save it

4、CMOSchecksumerror－Defaultsloaded
PressF1tocontnue?DELtoenterSETUP
08／09／2000－i810－ITE8712－6A69ME1CC－00
Cmos battery.
5、Warning！CPUhasbeenchanged！PleaseEnterCPUspeedCMOSsetupandRemembertosaveBeforeExit！
This shows the BIOS settings are washed away, to reset the BIOS (also called the CMOS settings). Power on while holding down the "Del" key to enter the settings, see your motherboard manual. Your CPU frequency? in the BIOS to selected FSB, multiplier anyway is locked. FSB always 66, 100, or 133, depends on the CPU type, from low to high settings. If the AWARD BIOS settings, select in Home/VoltageControl Frequency (frequency/voltage control), use this menu to on frequency, voltage, special setting. "ClockBySlightAdjust (clock frequency tuning)" allows you to select the CPU clock frequency. Other motherboard BIOS settings differ, you can refer to your motherboard manual.

6、cpuhasbeenchangedpleasere-entercpusettingsinthecmossetupandremembertosavebeforequit!
Some motherboards have a FSB jumper, the default is 100MHZ, also some motherboard does not support automatic FM. you as long as into the BIOS setting to the FSB in your CPU can be a standard FSB, multipliers generally is set automatically, it is best not to overclocking.

If the above solution does not solve the case, you can check the CMOS circuit is there next to burn out, my machine is because CMOS circuit next to the machine in question, pending methods are tried is useless, the last of a soldering iron. Oh, you also try!

No need to press F1 to enter system troubleshooting

In General, press F1 to enter system is the system's BIOS setting that does not affect the system startup caused by minor problems, so please check the BIOS settings of the hardware information and actual discrepancies.

Common fault is:

1, the motherboard battery.

Workaround: change the motherboard battery.

2, you set the floppydrive boot, but there is a problem with your floppy drive.

Workaround:

A, post press DEL to enter bios, boot off the floppy disk drive, the boot order to boot.

B, close on the floppy drive detection:

Start the computer, and then press the Enter key 【 Del 】 BIOS Setup main interface;

Select "AdvanCedBIOSFeatures "Settings item and press ENTER to enter;

Will "BootUpFloppySeek" set to "Disabled", so that you can turn off power on software testing capabilities.