【 Weak current College 】 post press F1 of causes and solutions

Whether you are experienced, will appear every time you post, "PressF1tocontinue DeltoenterSETUP", then the screen will not jump, you must first press the shortcut key F1, the computer can boot normally?
Post press F1 crash analysis?

In General, requires no press F1 to enter the system BIOS settings do not affect the system starts a small problem, first check the hardware information in the BIOS settings and actual discrepancies, usually have the following situation:

1, actually do not have a floppy disk drive or floppy disk drive is broken, and the BIOS is set to the floppy drive, this led to post press F1 to continue.

2. the original of the hanging two hard drives in the BIOS settings of a dual hard drives, then get off one when we forget the BIOS setting to come back, will also appear to post press F1.

3. motherboard battery has a will result in data loss to occur this failure.

4. reboot the system, enter BIOS settings and found that the floppy was set to 1.44M, but actually there is no floppy drive in the chassis, this key is set to NONE, troubleshooting.

Boot into the system by pressing F1 for a few common scenario solutions

1, the motherboard battery.

Workaround: change the motherboard battery.

2. set the floppy drive boot, but there is a problem with your floppy drive.

Solution: a, post press DEL to enter BIOS, boot off the floppy disk drive, the boot order to boot.

B, close on the floppy drive detection:

Start the computer, and then press the Enter key 【 Del 】 BIOS Setup main interface;

Select "settings," AdvancedBIOSFeatures press return to enter;

Will "BootUpFloppySeek" set to "Disabled", so that you can turn off power on software testing capabilities, and later do not need to post press F1 to start.

Post press F1 prompt detailed

Computer each boot to press F1 to normal startup problems when you are prompted to do so, adopt the appropriate measures.

1.CMOSbatteryfailed

Chinese: CMOS battery failure.

Explanation: This shows the CMOS battery is dead, as long as the motherboard battery removed and exchanged for a new battery. Most motherboards use 3V battery, don't be 5V batteries buy back! you just have to look closely at the cell surface you can see clearly marked "3V" above.

2.CMOSchecksumerror－Defaultsloaded

Chinese: CMOS executing all check error discovered, to load the system default value.

Explanation: in general the word is that the battery is almost out of power, you can try changing the battery, if the problem still not solved, there may be problems shows CMOSRAM, ordinary people do not experience, this information is mostly on the motherboard BIOS Flash will not complete, the only way is to Flash the BIOS, but cannot guarantee success.

If you haven't had a year to the dealer for a motherboard, a year will allow resellers to manufacturers fix!

3.PressESCtoskipmemorytest

Chinese: ongoing memory check, you can press ESC to skip.

Explanation: this is because there is no set within the CMOS to skip the memory of the second, third and fourth test, post executes four times the memory test, of course, you can press ESC to end the memory check, but every time you want to do too much trouble, you can access after selecting BIOSFEATURSSETUP COMS set, be QuickPowerOnSelfTest is set to Enabled, save it and restart the computer.

4.Keyboarderrorornokeyboardpresent

Chinese: keyboard error or no keyboard.

Explanation: check the keyboard cable is loose or damaged.

5.Harddiskinstallfailure

Chinese: hard drive installation failed.

Explanation: this is because the drive's power cord or cable may not connected or hard drive jumper is set incorrectly. You can check the root of the hard disk is plugged in line to see the same root data cable on two hard drive jumper settings are the same, if you like,as long as the two hard drive jumper settings are not the same (one is set to Master and the other as Slave) is also possible that the hard disk power cables, data cables may not connected or hard drive jumper is set incorrectly.

6.Secondaryslavehardfail

Chinese: detection from disk failures

Explanation: the CMOS settings may be inappropriate, for example from the disk but in CMOS is set to a slave, then an error occurs, you can enter the COMS set select IDEHDDAUTODETECTION automatically detect the hard drive. It may also be hard drive power cable and data cable may not connected or hard drive jumper is set incorrectly, solution reference section 5.

7.FloppYDisk (s) fail or FloppyDisk (s) fail (80) or FloppyDisk (s) fail (40)

Chinese: no driver floppy disk drive.

Explanation: you are prompted to find the floppy drive, see floppy drive power cable and data cable is loose or is wrong, or is the floppy drive into another computer's subnet, give it a try, if these are not, then had to buy another. If you do not have a floppy drive, we recommend CMOSSetup program "DriveA" set to "None".
8.Harddisk(s)diagnosisfail

Chinese: an error occurred while performing a hard disk diagnosis.

Explanation: this problem usually means that the hard disk itself fails, you can put the hard disk onto another camera on a try, if the problem is not resolved, you can only go to fix it.

9.Memorytestfail

Chinese: memory test failure.

Explanation: Reseat the memory modules, see if you can solve this problem occurs because memory stick General mutually incompatible, go-for-one!

10.Overrideenable－Defaultsloaded

Chinese: current CMOS settings cannot start the system, load BIOS default values in order to boot the system.

Explanation: in General is set within the COMS with error, just enter the COMS set select LOADSETUPDEFAULTS loading system to the original settings and then restart it.

11.PressTABtoshowPOSTscreen

Chinese: pressing the tab key to switch the screen display.

Explanation: some OEM manufacturers association to own design of the display to replace the BIOS default boot display, we can press the tab key to preset the BIOS splash and manufacturers of custom screen to switch between.

12.Resumingfromdisk，PressTABtoshowPOSTscreen

Chinese: boot from hard drive recovery, press tab to display the post screen).

Explanation: this is because some motherboard BIOS provides Suspendtodisk (hard disk hangs) function, if we use Suspendtodisk way to shut down, so we in the next post will display this message.

13.HarewareMonitorfoundanerror，enterPOWERMANAGEMENTSETUPfordetails，PressF1tocontinue，DELtoenterSETUP

Chinese: monitoring features found error, enter detailed information, see POWERMANAGEMENTSETUP press F1 to continue the boot process, press DEL to enter the COMS set.

Explanation: some motherboards have hardware monitoring feature, you can set the motherboard and CPU temperature monitor, voltage regulator of voltage output bit monitor and on each fan speed monitoring, when the monitoring features in the find exception when powered on, it will appear above this line, then you can enter the COMS set select POWERMANAGEMENTSETUP, in the right ** FanMonitor **, ** ThermalMonitor ** and ** VoltageMonitor ** view which part issued an exception, and then to be addressed.

14、Displayswitchissetincorrectly

Chinese: display switch configuration error

Solution: If your motherboard is old, it certainly does not appear on this information. In General, the old motherboard on which there is a route is used to set the screen for monochrome or color. This information indicates that the setting on the motherboard and the CMOS settings are not consistent, so as long as the judgment of the Board and the CMOS settings who is correct, and then update the wrong settings.

15、Harddisk(s)initializing(Pleasewaitamoment…)

Chinese: on the hard disk initialization, please wait a moment

Solution: this kind of information to a new hard disk is not seen, but in older hard disk, because the slow, so you will see this information.