【 Weak current college 】 computer hardware malfunction surf 3---Power By 【 China power house network 】

computer failure of <br> ★ ★ <BR> <BR> burner Troubleshooting chapter one: can not start after installation of the computer recorder <BR> <BR> First off the computer power supply, check the IDE cable to open the case cover is fully inserted into the .and to ensure that PIN-1 position of the pins connected correctly. .If the writer shared with other IDE devices one IDE cable, ensure that two devices can not be set to "MA" (Master) or "SL" (Slave), it can be set to a "MA", a setting for " .SL ". .<BR> <BR> Troubleshooting II: successful use of analog recording, the actual recording but failed <BR> <BR> recorder provided by the "analog recording" and "burn" command is whether the difference between playing a laser beam, and other operations .are exactly the same, that is, "Analog recording" to test the source disc is normal, hard disk speed is fast enough, enough free disk space environment conditions such as burning, but can not burn the disc to be tested if there are problems and .burner laser power and disc read-write head matches and so on. .In view of this, that "analog recording" successful, but the real burn fails, the recorder and blank disc compatibility is not good, the following two methods can be used to re-try it: <BR> <BR> 1 .. lower burner write speed, 2X recommended the following; <BR> <BR> 2. to replace another brand of blank disc to burn operation. .There's another reason why this phenomenon is the phenomenon of laser power attenuation caused by read-write head, and if you use the same brand of disc burning, the first time were normal, it is likely related to power loss and the head can be sent to the relevant .vendor maintenance. .<BR> <BR> Fault Three: Can not copy the game CD <BR> <BR> some large commercial software or game software, in the production process, the protection of the CD disc to do so during the process of copying CD-ROM .in, there will not be copied, resulting in the burning process the error occurred, or not work after copying to happen. .<BR> <BR> Fault IV: Burning the CD music can not play properly <BR> <BR> not all of the audio equipment can be properly read CD-R discs, most can not read normal CD drive .CD-RW disc's contents, so it is best not to use the CD burner to burn music. .In addition, you also need to note that burn music CD, CD-DA must comply with the file format. .<BR> <BR> Five common faults: the process of burning software to burn the disc, sometimes "BufferUnderrun" error message <BR> <BR> "BufferUnderrun" error message means for the buffer underrun. .Usually in the burning process, data needs to be burning through the IDE hard disk interface by the sending to the host, and then transmitted via the IDE interface to the recorder in the cache (BufferMemory), the last writer to store data inside the BufferMemory burned to CD- .R or CD-RW discs, these actions must be continuous, must not be interrupted, if any one part of a problem, it will not work cause the recorder to write data, and a buffer underrun error prompt, and then .is the disc scrapped. .The solution is, before the burning need to close some memory-resident programs, such as turn off CD auto insert notification, disable antivirus software, Window task management and task scheduler and the screen saver and more. .<BR> <BR> Troubleshooting Six: CD burning process, they would often fail <BR> <BR> burn burn success rate needs to improve the environment to keep the system simple, that is, turn off the background resident program, it is best to prepare one for the recording system .Dedicated hard drive, specifically related to software installation and burning. .In the burning process, the better the data stored in the hard drive first, made into"ISO image file" and then carved into the disc. .The burning process in order to ensure smooth data transfer, you need to sort out debris often hard to avoid not work because the file transfer, the error interruption caused by the burning, you can perform "ScanDisk" and "Disk Defragmenter" to organize the hard disk .. .In addition, in the burning process, do not run other programs, even the mouse and keyboard is not going to touch lightly. .Best not to burn the use of computer and other computer networking, in the burning process, if the system administrator to send messages to the machine, will affect the burn effect, In addition, the LAN, do not use resource sharing, if the burning process, other .users to read the local hard disk, can cause interruptions or failure of the recording. .In addition, the recorder should note that the heat dissipation problem, good heat dissipation will give a stable burner work environment, if for a continuous recorder, burner heat is too high, you can turn off the computer, such as the temperature continues to decrease at a later .burning. .Built-in recorder for the best in the chassis with extra cooling fan. .External recording confidential attention to dust, moisture, so as to avoid laser to read and write is not normal. .<BR> <BR> Seven common faults: use EasyCDPro recorder does not recognize the name of the directory <BR> <BR> Chinese EasyCDPro burning in the use of Chinese file name, they can select the option in the file name Romeo, can support up to 128 .bit file name, that is 64 characters in the file name of the. .In addition, WinonCD, Nero, DirectCD2.x so the Chinese can be a good support long file names, EasyCDCreator a little trouble in this respect some..