College】 【weak computer hardware failure Raiders 5 --- Power By 【China】 weak home network.

computer failure of the drive <br> ★ ★ <BR> <BR> articles drive is the shortest life of computer hardware components in one. .In fact, many scrap the drive there is still much of value, just click on it a little maintenance. .This often do not have any profound knowledge of radio, do not need anything too complicated to use the repair tools and materials. .Just look carefully and with reference to the implementation of the following symptoms of some troubleshooting, I believe you can still restore the old drive past "style" of. .<BR> <BR> A common failure: hard disk drive light is always flashing work <BR> <BR> This is an illusion, it is not. .Because of the hard disk light flashes and the hard disk drive with an IDE interface connected, the disc also control the hard work the results of light. .Drive unit can be connected to a single IDE interface. .<BR> <BR> Fault Two: In the Windows environment to operate on the CD-ROM to display "32 disk access failed", and then crashes <BR> <BR> Obviously, Windows 32-bit disk access on CD- .ROM to a certain extent. .Most CD-ROM connected to the IDE hard drive interface does not support Windows 32-bit disk access, the Windows generated an internal error crash. .After entering Windows, the "main group" double-click "Control Panel" and enter "386 Enhanced Mode" setting, click the "Virtual Memory" button and then click "Change", the lower left corner of the "32-bit disk access" .check box is closed, the confirm, then restart Windows, in Windows, and then access the CD-ROM will not go into error. .<BR> <BR> Fault Three: drive can not properly read the disk, displayed on the screen: "There is no disk drive X, insert the disk again", or "CDR101: NOTREADYREADINGDRIVEXABORT.RETRY.FALL?" Out of box a few times also occasionally .have read the disk, but soon not read the disk. .<BR> <BR> In this case, the virus should be detected by antivirus software on the machine to check anti-virus, the virus can not find the file if the editor to open C under the root directory of the CONFIG.SYS "file to see which .if they put up light drivers and drivers are broken, and processing, but also with a text editing software View "AUIOEXEC.BAT" file for "MSCDEX.EXE / D: MSCDOOO / M: 20 / V". If .No issues were found more than two steps, removable drive maintenance. <BR> <BR> Troubleshooting four: drive when using the read-write errors or diskless <BR> <BR> prompted most of this phenomenon in the changer Shihai .No place to operate on the drive caused by the fault. for all the operations drive will need to wait for the CD like the bit when the indicator shows the operation can be conducted. In Play DVD when the time should also be transferred to zero and then .changer, which can avoid the above error. <BR> <BR> five common faults: when playing VCD movies pause or broken screen phenomenon <BR> <BR> check the AUTOEXEC.BAT file "SMARTDRV" whether the .on MSCDEX.EXE after. If so, you should put MSCDEX.EXE SMARTDRV statement before; Party not to use high-speed CD-ROM rushed process to SMARTDRV.EXE / U; failure can be ruled out. <BR> <BR> .Troubleshooting Six: CD-ROM in the read data, read and sometimes not, and the longer the time to read the disk drive <BR> <BR> not read the disk hardware failure focused on the laser head assembly, and can be divided into two .kinds of situations: one is caused by using long laser tube aging; the other is the photocell lens surface is dirty or dirty and displacement of the laser tube deformation. So the power to adjust the laser tube, the need for optical and laser tube .tube lens cleaning. <BR> <BR> phototube and focusing lens cleaning method is: Disconnect the laser head assembly, aflat cable, remember that direction, open the laser head assembly. this time to see .hooded jacket laser focusing lens, remove the jacket will find that focusing lens from the four fine copper wire connected to the focus, tracing the coil, the optical tube assembly is installed in the bottom of the hole in the lens. with a fine wire .wrapped in clean cotton stick a small amount of distilled water (not with an alcohol wipe the surface of optical lens tube and focus), and to see whether the level of the lens on the laser tube is suspended, it shall be adjusted appropriately. Thus, the cleaning is completed. <BR> <BR> adjustment .laser power. in the side of the laser head assembly screws are a little like a cross potentiometer. the use of color and write the initial position, generally the first clockwise 5 ° ~ 10 °, not re-installed test machine counter-clockwise .5 ° ~ 10 °, until it can successfully read the disk. attention must not rotate too much, so much power and burned photocell. <BR> <BR> seven common faults: not detected CD-ROM drive or the boot test failed <BR> < .BR> This may be the optical drive data cable connector is loose, damaged or the hard disk drive data cable jumper settings cause the error encountered this problem, we should first check the drive's data cable connector is loose, if we find there is no plug .well, it will be re-plugged, plug tight. If this does not resolve the fault, we recruited a new data can be put on line to try. this time if the fault persists, we need to check the CD-ROM .jumper settings, if there is an error, change it to. <BR> <BR>.