【 Weak current College 】 burner of some fault---Power By 【 China power house network 】

A common fault: installed burner computer fails to start after

First cut off the computer power supply, open chassis coat check is fully inserted into the IDE cable, and to ensure that the pin location PIN-1 connected properly. If the recorder and the other IDE device share an IDE cable, required to ensure that the two devices cannot be set to "MA" (Master) or "SL" (Slave), you can make a set to one of the "MA," SL "set to".

Common fault II: using simulation burned successfully, the actual recording has failed

Burner to burn the "analog" and "burn" command to see whether there is a difference between the laser beam, but other operations are identical
; That is, "simulation of recording" you can test the source CD is normal, the hard drive speed is fast enough, the remaining disk space is enough to burn the condition of the environment, but you cannot test question to burn disc for problems and burner laser to read and write head power and disc matches, and so on. For this reason, the "simulation" successful burn a real burn failed, the burner and blank disc compatibility is not very good, you can use the following two methods to try it out:
1. reduce the write speed to burn machine, the following proposed 2X;
2. replace another brand of blank discs burning operation. This phenomenon of another reason is the laser to read and write head power decay, if you use the same brand of disc burning, during the previous period are OK, it is likely and read-write head power attenuation, you can send the manufacturer for repair.

Three common failure: unable to copy the game CD

Some large commercial software or the game software, in the production process, on the CD-ROM disc made protection, so the CD replication process, you cannot copy occurs, leading to the burning process error occurs, or replication does not use later.

Four common fault: burning CD music does not play correctly

Not all audio equipment properly read CD-R disc CD player, most are not properly read the contents of a CD-RW disc, so it is best not to use the burner to burn music CD. In addition, also note that burned CD music, must meet CD-DA file format.

Five common fault: burning software to burn the disc, sometimes appear "BufferUnderrun" error message

"BufferUnderrun" error message mean as a buffer underrun. Usually in the burn process, you need to burn the data from the hard drive after
About IDE interface to the host through the IDE interface is transmitted to the recorder's cache (BufferMemory), and finally the recorder to store in the
BufferMemory data information to burn to a CD-r or CD-RW disc, these actions must be contiguous, and must not be interrupted, if any one of the links, will cause the recorder does not write data, and a buffer underrun error prompts, which in turn is disc scrap. The solution is to burn before the permanent memory required close some programs, such as closing the CD auto-insert notification, turn off anti-virus software, Window Task Manager and Task Scheduler and screen saver, etc.

Six common fault: CD burning, burn failure occurs frequently

Improve burn rate need to be kept simple, that is, the system environment to close the background to the program, it is best to burn system prepares a dedicated hard disk dedicated to installation and burn-related software. In the recording process, it is best to put the data to be saved on your hard disk, making "the ISO image file" and then carved into the disc. In order to ensure that the burning process data transfer smooth, often on the hard disk for finishing, to avoid for file does not transfer, by burning interrupt error, you can perform "ScanDisk" and "Disk Defragmenter to defragment the hard disk". In addition, the burning process, do not run other programs, even the mouse and keyboard will not go easily touch. Burn it is better not to use the computer and other computers on a network, the burning process, if the system administrator to send information to the native, will affect the burn effect, also, in the local area network, do not use resource sharing, if in the burning process, other users to read the local hard disk, burn a work disruption or failure. In addition, we must pay attention to the problem of heat burner, good thermal conditions will give writers a stable work environment, if because of continuous recording, the burner heat too high, you can turn off the computer, such as the temperature decreases continue later burned. For built-in burner best in-the-box with extra cooling fans. External burner it is necessary to pay attention to dust-proof, moisture-proof, so as to avoid the laser head, reading and writing is not working properly.

Seven common fault: use EasyCDPro burn does not recognize the Chinese directory name

In the file name of the burners using EasyCDPro Chinese, you can select the file name option, you can support the Romeo up to 128-bit file
Name, i.e. 64 characters of the filename. In addition, WinonCD, Nero, DirectCD2.x and so can support long file names, Chinese