【 Weak current College 】 printer of some fault---Power By 【 China power house network 】

In the Office, inkjet printers are using more general will of a device. Inkjet printer because of the use, maintenance, improper operation, these reasons some fault occurs frequently, and how to address the concerns of the users. In this we will daily work are the common fault of summed up, and I hope to everyone to help.

A common fault: printing ink scarce, illegible handwriting, the fault is the cause of most unused because the printer is long-term or for other reasons, causing the ink delivery system disorder or nozzle clogging.

Troubleshooting: If the anti-plug himself very badly, then the direct execution of cleaning the printer on. If multiple no effect after cleaning, you can get the cartridges (for non-integrated cartridge nozzles, there is a need to pursue nozzle printer, but requires careful), put the nozzle on a warm dip in a note, be sure not to put the Board part is immersed in water, otherwise the tad sucked away by blotting paper stained with drops of water, with some time after cleaning nozzle.

Common fault 2: replace the new cartridge, the printer is in power Panel "ink" lights of processing

Normally, when the ink has run out of time "ink" lamp will be lit. Replacement ink cartridges, printer Panel "ink" light, this failure is possible, a cartridge is not installed, another possibility is in shutdown state to take on the old cartridge, and replace the new cartridge. Because once again replacement ink cartridges, printer ink delivery system will be filled with ink, and this process in shutdown state does not work, make the printer cannot detect the reinstall the ink cartridges. In addition, some printer ink capacity measurement is to use the printer's internal electronic counter to count (especially on color ink usage statistics), when the counter reaches a certain value, the judge exhausting ink printer. And in the ink cartridge replacement procedure, the printer will on their internal electronic counters are reset to confirm that you have installed a new ink cartridge.

Solution: turn on the power, will head to the ink cartridge replacement position. The cartridge installed, let printer ink-filled, filling ink process is finished, troubleshooting.

Three common fault: nozzle soft plug of processing

Soft plug plug is for various reasons the ink in the nozzles on the viscosity gets bigger by the broken line failure. General use original ink cartridges after repeated cleaning can be restored, but this method is a waste of ink. The simplest way is to use your hands to the empty ink cartridge cleaning nozzle. Use an empty ink cartridge cleaning before using needles in residual ink cartridge as far as possible, the better, cleaner and then join the cleaning liquid (accessories market sale). When annotating the cleaning fluid, clean environment, combined with good washing of ink by printer normal operating computer, continuously press the printer cleaning key to cleaning. Using the ink cartridge cleaning residual ink and in mixed light color print test, after change fine normally cartridge can be used.

Four common fault: printer cleaning pump nozzle of fault handling

Printer cleaning pump nozzle acted more, also contribute to plug one of the major factors. Printer cleaning pump nozzle on printer nozzle protection plays a decisive role. Nozzle car back in place, the cleaning pump nozzle on a weak suction nozzles, conducted on the sprinkler protection seal. Install a new cartridge in the printer or nozzle has a broken line, machine at the lower end of the suction pump to carry through its exhaust nozzles, the nozzles work accuracy higher the better. But in actual use, its performance and tightness due to time, dust and ink in the mouth of residue solidification of increase and decrease. If the consumer does not constantly check or cleaning, it will make your printer nozzle constantly out failures.

Conservation of this part of the way: the printer's top cover removed removed trolley, needle aspiration and pure water for irrigation, especially on the mouth of microporous gasket in mosaic full cleaning. In this to remind the user to clean the parts mustn't with ethanol or methanol cleaning it, causing this component of microporous gasket solvent mosaic. In addition to the ink jet printer to as far away as possible from high temperature and dusty environment, only a good working environment in order to ensure the normal use of the machine for long.

Five common fault: detect verticle lines normal and print accuracy significantly worse treatment

Inkjet printer in use will vary depending on the use of the frequency and timing of extension and print accuracy becomes poor. Inkjet printer nozzle is life. Usually a new nozzle from starts using the end-of-life, if no failures more smoothly, which is 20-40 ink usage life. If your printer is used for a long time, now of print accuracy, you can replace the ink cartridge of methods to try, if you change the cartridge, the results of its output print are the same, then your printer nozzle to be replaced. If there is a change in the future replace the ink cartridge, you may use the cartridge in a poor quality of non-original ink.

If the printer is new, the printed results cannot satisfy you, frequent print segment is not clear, text graphics, skew, text graphics outer boundaries blur, print out the ink control synchronization accuracy is poor, this means you may get a false cartridge or cartridges are used by the original product, it should be replaced immediately.

Six common fault: walking trolley handle dislocated to meet

Inkjet printer walking trolley track consists of two powder alloy copper sleeves and a combination of precision steel shaft to slip through. While walking on the car design and installation of a film of oily felt washer to complement the axis on lubricating oil, but because we live in an environment where there is dust everywhere, with the passage of time, will air oxidation, dust and damage the shaft surface aging and expiration of lubricating oil, then if you continue to use the printer, because the axis and copper sleeve friction increases the dislocation resulting trolley until collision front result cannot be used.
BR > the solution is: If this fault should immediately turn off the printer power supply, by hand will not return the car to push back to the parking. Find a small piece of sponge or felt, in sewing machine oil immersed in oil, use pliers wipe around on the spindle. It's best to spindle down to wash the oil, the best results.

Meet another car is damaged because of a device. Printer cart parking above a photoelectric sensor, it is the printer system board provides print car reset signal of important components. This component if the dust is too large or corrupted printer car will not find return signal hits the front, which is not available when the failure of general out this device needs to be replaced.